#ifndef PROSWEEP_H
#define PROSWEEP_H
#include <ProToolkit.h>
#include <ProBodyOpts.h>
PRO_BEGIN_C_DECLS
/************************ SWEEP ********************************
Feature element tree
PRO_E_FEATURE_TREE
|
|---PRO_E_FEATURE_FORM
|---PRO_E_SWEEP_TYPE
|
|---PRO_E_SWEEP_FRAME_COMP
| |---PRO_E_FRM_OPT_TRAJ
| | |---PRO_E_OPT_TRAJ
| | |---PRO_E_STD_SEC_METHOD
| | |
| | |---PRO_E_STD_SEC_SELECT
| | |---PRO_E_STD_CURVE_COLLECTION_APPL
| |
| |
| |---PRO_E_FRAME_SETUP
| | |---PRO_E_FRM_NORMAL
| | |---PRO_E_FRM_PIVOT_DIR
| | | |---PRO_E_DIRECTION_COMPOUND
| | | |---PRO_E_DIRECTION_REFERENCE
| | | |---PRO_E_DIRECTION_FLIP
| | |---PRO_E_FRM_CONST_Z
| | | |---PRO_E_DIRECTION_COMPOUND
| | | |---PRO_E_DIRECTION_REFERENCE
| | | |---PRO_E_DIRECTION_FLIP
| | |---PRO_E_FRM_ORIENT
| | |---PRO_E_FRM_NORM_SURF (COMPOUND)
| | | |---PRO_E_SURF_CHAIN_CMPND
| | | | |---PRO_E_SURF_CHAIN_METHOD
| | | | |---PRO_E_SURF_CHAIN_REF_SURFS
| | | |---PRO_E_FRM_NORM_SURF_SIDE
| | |---PRO_E_FRM_USER_X
| | |---PRO_E_FRM_START_X
| | | |---PRO_E_DIRECTION_COMPOUND
| | | |---PRO_E_DIRECTION_REFERENCE
| | | |---PRO_E_DIRECTION_FLIP
|---PRO_E_SWEEP_PROF_COMP
| |---PRO_E_SWP_SEC_TYPE
| |---PRO_E_SWEEP_SECTION
| |
| |---PRO_E_SKETCHER POINTER
|---PRO_E_SWP_ATTR
| |---PRO_E_END_SRF_ATTR
|
|---PRO_E_STD_FEATURE_NAME
|---PRO_E_EXT_SURF_CUT_SOLID_TYPE
|---PRO_E_REMOVE_MATERIAL
|---PRO_E_FEAT_FORM_IS_THIN
|---PRO_E_STD_MATRLSIDE
|---PRO_E_THICKNESS
|---PRO_E_TRIM_QUILT
|---PRO_E_TRIM_QLT_SIDE
|---PRO_E_BODY
| |--PRO_E_BODY_USE
| |--PRO_E_BODY_SELECT
| *** The Following elements are applicable only in sheetmetal parts ***
|---PRO_E_STD_SMT_THICKNESS
|---PRO_E_STD_SMT_SWAP_DRV_SIDE
|---PRO_E_SMT_WALL_SHARPS_TO_BENDS
|---PRO_E_SMT_FILLETS
| |---PRO_E_SMT_FILLETS_SIDE
| |---PRO_E_SMT_FILLETS_VALUE
|---PRO_E_SMT_DEV_LEN_CALCULATION
| |---PRO_E_SMT_DEV_LEN_SOURCE
| |---PRO_E_SMT_DEV_LEN_Y_FACTOR
| | |---PRO_E_SMT_DEV_LEN_Y_FACTOR_TYPE
| | |---PRO_E_SMT_DEV_LEN_Y_FACTOR_VALUE
| |---PRO_E_SMT_DEV_LEN_BEND_TABLE
|---PRO_E_SMT_MERGE_DATA
| |---PRO_E_SMT_MERGE_AUTO
| |---PRO_E_SMT_MERGE_KEEP_LINES
|
|--PRO_E_SMT_NEW_BODY_LINKED
|
*************************************************************************/
/*
------------------------------------------------------------------------------
Element Id Element Name Data Type
------------------------------------------------------------------------------
PRO_E_FEATURE_FORM Feature Form PRO_VALUE_TYPE_INT
PRO_E_SWEEP_TYPE Sweep Type PRO_VALUE_TYPE_INT
PRO_E_SWEEP_FRAME_COMP Sweep Frame Compound
PRO_E_FRM_OPT_TRAJ Trajectories Array Array
PRO_E_OPT_TRAJ Trajectory Compound
PRO_E_FRAME_SETUP Frame setup Compound
PRO_E_FRM_NORMAL Sect. plane normal PRO_VALUE_TYPE_INT
PRO_E_FRM_PIVOT_DIR Proj Dir. holder Compound
PRO_E_FRM_CONST_Z Const Z Dir. holder Compound
PRO_E_DIRECTION_COMPOUND Direction Element Compound
PRO_E_FRM_Z_CHOICE_BTN Normal traj index PRO_VALUE_TYPE_INT
PRO_E_FRM_ORIENT Sect. Horiz/Vert PRO_VALUE_TYPE_INT
PRO_E_FRM_NORM_SURF Normal surf. holder Compound
PRO_E_SURF_CHAIN_CMPND Surfaces from chain Compound
PRO_E_FRM_NORM_SURF_SIDE Normal surf. side PRO_VALUE_TYPE_INT
PRO_E_FRM_USER_X User sel. start X PRO_VALUE_TYPE_INT
PRO_E_FRM_START_X Start X Dir holder Compound
PRO_E_FRM_X_CHOICE_BTN X traj. index PRO_VALUE_TYPE_INT
PRO_E_FRM_TRAJS_APPENDIX Hidden traj. block PRO_VALUE_TYPE_SELECTION
PRO_E_SWEEP_PROF_COMP Sweep Sect. holder Compound
PRO_E_SWP_SEC_TYPE Section type PRO_VALUE_TYPE_INT
PRO_E_SWEEP_SECTION Section Compound
PRO_E_SWP_ATTR Sweep Attributes Compound
PRO_E_END_SRF_ATTR End Cap PRO_VALUE_TYPE_INT
PRO_E_STD_FEATURE_NAME Feature Name PRO_VALUE_TYPE_WSTRING
PRO_E_EXT_SURF_CUT_SOLID_TYPE Feature Type PRO_VALUE_TYPE_INT
PRO_E_REMOVE_MATERIAL Material Removal PRO_VALUE_TYPE_INT
PRO_E_FEAT_FORM_IS_THIN Feature Form PRO_VALUE_TYPE_INT
PRO_E_STD_MATRLSIDE Material Side PRO_VALUE_TYPE_INT
PRO_E_THICKNESS Thin width PRO_VALUE_TYPE_DOUBLE
PRO_E_TRIM_QUILT Trim Quilt PRO_VALUE_TYPE_SELECTION
PRO_E_TRIM_QLT_SIDE Quilt Side PRO_VALUE_TYPE_INT
PRO_E_BODY Body options Compound
PRO_E_BODY_USE Body use option PRO_VALUE_TYPE_INT
PRO_E_BODY_SELECT Selected body ref PRO_VALUE_TYPE_SELECTION
PRO_E_STD_SMT_THICKNESS Smt Thickness PRO_VALUE_TYPE_DOUBLE
PRO_E_STD_SMT_SWAP_DRV_SIDE Smt Swap Side PRO_VALUE_TYPE_INT
PRO_E_SMT_WALL_SHARPS_TO_BENDS Edges to Bends PRO_VALUE_TYPE_INT
PRO_E_SMT_FILLETS Smt Fillets Compound
PRO_E_SMT_FILLETS_SIDE Smt Radius Side PRO_VALUE_TYPE_INT
PRO_E_SMT_FILLETS_VALUE Smt Radius Value PRO_VALUE_TYPE_DOUBLE
PRO_E_SMT_DEV_LEN_CALCULATION Smt Develop Length Compound
PRO_E_SMT_DEV_LEN_SOURCE Smt Dev Len Source PRO_VALUE_TYPE_INT
PRO_E_SMT_DEV_LEN_Y_FACTOR Smt Dev Len Y Fact Compound
PRO_E_SMT_DEV_LEN_Y_FACTOR_VALUE Y Factor Value PRO_VALUE_TYPE_DOUBLE
PRO_E_SMT_DEV_LEN_Y_FACTOR_TYPE Y Factor Type PRO_VALUE_TYPE_INT
PRO_E_SMT_DEV_LEN_BEND_TABLE Smt Dev Bend Table PRO_VALUE_TYPE_INT
PRO_E_SMT_MERGE_DATA Smt Merge Wall Data Compound
PRO_E_SMT_MERGE_AUTO Auto Merge Wall PRO_VALUE_INT
PRO_E_SMT_MERGE_KEEP_LINES Keep Merged Lines PRO_VALUE_INT
PRO_E_SMT_NEW_BODY_LINKED Link Smt Body to Part PRO_VALUE_TYPE_OPTION
*/
/************************************************************************
PRO_E_FEATURE_FORM required type ProFeatFormType (see ProFeatForm.h)
valid value PRO_SWEEP
PRO_E_SWEEP_TYPE required type pro_sweep_type
valid value PRO_SWEEP_TYPE_MULTI_TRAJ
PRO_E_STD_FEATURE_NAME required Default given by application depending
on feature type.Can be modified by user.
PRO_E_EXT_SURF_CUT_SOLID_TYPE required type pro_sweep_feat_type
valid values PRO_SWEEP_FEAT_TYPE_SOLID
PRO_SWEEP_FEAT_TYPE_SURFACE
PRO_E_REMOVE_MATERIAL requied type pro_sweep_rem_material
valid values PRO_SWEEP_MATERIAL_ADD
PRO_SWEEP_MATERIAL_REMOVE
PRO_E_FEAT_FORM_IS_THIN requied for thin feature
type pro_sweep_feat_form
valid values PRO_SWEEP_FEAT_FORM_NO_THIN (default)
PRO_SWEEP_FEAT_FORM_THIN
PRO_E_STD_MATRLSIDE requied for thin feature or cut
type pro_sweep_material_side
valid values PRO_SWEEP_MATERIAL_SIDE_ONE
PRO_SWEEP_MATERIAL_SIDE_TWO
PRO_SWEEP_MATERIAL_BOTH_SIDES
PRO_E_THICKNESS required for thin feature
type PRO_VALUE_TYPE_DOUBLE
valid value > 0.0
PRO_E_TRIM_QUILT required for surface trim
type PRO_VALUE_TYPE_SELECTION
selection of type Quilt
PRO_E_TRIM_QLT_SIDE required for two sided surface trim i.e.
if pro_sweep_material_side is
PRO_SWEEP_MATERIAL_BOTH_SIDES
type pro_sweep_trimqlt_side
valid values PRO_SWEEP_TRIMQLT_SIDE_ONE
PRO_SWEEP_TRIMQLT_SIDE_TWO
PRO_E_FRM_OPT_TRAJ required array of trajectories ( PRO_E_OPT_TRAJ ).
Only one (origin) traj supported in Creo Parametric TOOLKIT.
PRO_E_OPT_TRAJ trajectory (selected section instance).
PRO_E_FRM_NORMAL required
type pro_frame_normal
valid values PRO_FRAME_NORM_ORIGIN
PRO_FRAME_PIVOT_DIR
PRO_FRAME_CONST_Z_DIR
PRO_E_FRM_PIVOT_DIR used and required only if PRO_E_FRM_NORMAL is
PRO_FRAME_PIVOT_DIR.
compound holder of direction elem.for pivot dir
of type PRO_E_DIRECTION_COMPOUND
See ProDirection.h
PRO_E_FRM_CONST_Z used and required only if PRO_E_FRM_NORMAL is
PRO_FRAME_CONST_Z_DIR
compound holder of direction elem.for const Z dir.
of type PRO_E_DIRECTION_COMPOUND
See ProDirection.h
PRO_E_FRM_ORIENT required
type enum pro_frame_orient
valid values PRO_FRAME_MIN
PRO_FRAME_NORM_SURF
PRO_FRAME_CONSTANT
PRO_E_FRM_NORM_SURF required if PRO_E_FRM_ORIENT is PRO_E_FRAME_NORM_SURF
holder of Surf Chain element
Surf Chain Method should be populated
Valid values PRO_SURF_CHAIN_METHOD_DEFAULT1,
PRO_SURF_CHAIN_METHOD_DEFAULT2
PRO_E_SURF_CHAIN_METHOD_DEFAULT2 is the default.
The other can be used only if
the trajectory is comprised of two sided edges.
see ProSurfchain.h
PRO_E_FRM_NORM_SURF_SIDE required if PRO_E_FRM_ORIENT is PRO_E_FRAME_NORM_SURF
type pro_frm_norm_srf_side
valid values PRO_FRAME_NORM_SRF_SIDE_INSIDE
PRO_FRAME_NORM_SRF_SIDE_OUTSIDE
PRO_E_FRM_USER_X needed if PRO_E_FRM_ORIENT is PRO_FRAME_MIN
type pro_frame_start_x
valid values PRO_FRAME_DEFAULT_START_X (default)
PRO_FRAME_USER_START_X
If not default, then a direction must be provided
in PRO_E_FRM_START_X.
PRO_E_FRM_START_X used and required only if PRO_E_FRM_USER_X is
PRO_FRAME_USER_START_X
compound holder of direction element for X direction
at start, of type PRO_E_DIRECTION_COMPOUND.
See ProDirection.h
PRO_E_SWEEP_PROF_COMP compound holding Sweep Section related elements
PRO_E_SWP_SEC_TYPE required
type pro_sweep_sec_type
In Creo Parametric TOOLKIT only PRO_SWEEP_CONST_SECTION (= 8388608)
supported.
PRO_E_SWEEP_SECTION required - Instance of PRO_E_STD_SECTION see
ProStdSection.h
For more details refer ProStdSection.h
See notes below for usage in Sweep
PRO_E_END_SRF_ATTR used only for surface feature.
type pro_sweep_end_srf_attr
valid values PRO_SWEEP_END_SRF_OPEN (default)
PRO_SWEEP_END_SRF_CAPPED
PRO_E_BODY Compound element
PRO_E_BODY_USE Mandatory
To which body feature adds geometry
Valid values:
PRO_BODY_USE_NEW
Feature stores its geometry in new body
PRO_BODY_USE_SELECTED
Feature adds its geometry to single selected body
PRO_E_BODY_SELECTED Reference to selected body
Mandatory if PRO_E_BODY_USE is set to PRO_BODY_USE_SELECTED
Ignored otherwise
Single reference allowed
PRO_E_SMT_NEW_BODY_LINKED see ProExtrude.h
***********************************************************************/
/************************************************************************
Direction elements holders: see ProDirection.h
PRO_E_FRM_PIVOT_DIR used and required only if PRO_E_FRM_NORMAL is
PRO_FRAME_PIVOT_DIR.
PRO_E_FRM_CONST_Z used and required only if PRO_E_FRM_NORMAL is
PRO_FRAME_CONST_Z_DIR
PRO_E_FRM_START_X set and required only if PRO_E_FRM_USER_X is
PRO_FRAME_USER_START_X
***********************************************************************/
/**************************
Element tree for sweep trajectories (selected section ).
This is one intance of selected section
(others used in Swept Blend and Blends).
PRO_E_OPT_TRAJ
|---PRO_E_STD_SEC_METHOD
|
|---PRO_E_STD_SEC_SELECT
| |---PRO_E_STD_CURVE_COLLECTION_APPL
|
|---PRO_E_SKETCHER
------------------------------------------------------------------------------
Element Id Element Name Data Type
------------------------------------------------------------------------------
PRO_E_OPT_TRAJ Traj Holder Compound
PRO_E_STD_SEC_METHOD Section Method PRO_VALUE_TYPE_INT
PRO_E_STD_SEC_SELECT Selected section Compound
PRO_E_STD_CURVE_COLLECTION_APPL Trajectory chain PRO_VALUE_TYPE_SELECTION
PRO_E_STD_SEC_METHOD required valid value PRO_SEC_SELECT (= 26) defined in
ProStdSection.h.
PRO_E_STD_SEC_SELECT Selected trajectory holder
PRO_E_STD_CURVE_COLLECTION_APPL required chain reference
see ProCrvcollection.c
************************************************************************/
/************surf chain -- *******************/
/* PRO_E_SURF_CHAIN_CMPND */
/*
PRO_E_SURF_CHAIN_CMPND
|---PRO_E_SURF_CHAIN_METHOD
|---PRO_E_SURF_CHAIN_REF_SURFS
| |---PRO_E_SURF_CHAIN_SURF
| | |---PRO_E_SURF_CHAIN_REF
*/
/*
------------------------------------------------------------------------------
Element Id Element Name Data Type
------------------------------------------------------------------------------
PRO_E_SURF_CHAIN_CMPND Surface from curve chain Compound
PRO_E_SURF_CHAIN_METHOD Method PRO_VALUE_TYPE_INT
PRO_E_SURF_CHAIN_REF_SURFS Reference surfaces Array
PRO_E_SURF_CHAIN_SURF Reference surfaces Compound
PRO_E_SURF_CHAIN_REF Reference PRO_VALUE_TYPE_SELECTION
*/
/************************************************************************/
/* PRO_E_SURF_CHAIN_METHOD */
typedef enum pro_surf_chain_method
{
PRO_SURF_CHAIN_METHOD_NOINIT = 0,
PRO_SURF_CHAIN_METHOD_DEFAULT1 = (1<< 0), /* side 1 of the chain */
PRO_SURF_CHAIN_METHOD_DEFAULT2 = (1<< 1), /* side 2 of the chain */
PRO_SURF_CHAIN_METHOD_SKETCH = (1<< 2),
PRO_SURF_CHAIN_METHOD_SELECT = (1<< 3),
PRO_SURF_CHAIN_METHOD_NONE = (1<< 4)
}ProSurfChainMethod;
/*
For PRO_E_FRM_NORM_SURF, needed if PRO_E_FRM_ORIENT is PRO_E_FRAME_NORM_SURF
only PRO_E_SURF_CHAIN_METHOD_DEFAULT1, PRO_E_SURF_CHAIN_METHOD_DEFAULT2
are supported. Both are available only if the trajectory is comprised of
two sided edges.
*/
/***********************end of surf chain **********************************/
/***********************************************************************/
/* PRO_E_SWEEP_PROF_COMP */
/* holder of section related elements, mostly PRO_E_SWEEP_SECTION */
/* PRO_E_SWEEP_SECTION */
/* Instance of standard section */
/* For more details refer ProStdSection.h */
/* Note that for this feature the PRO_E_SEC_USE_SKETCH is not available,
and the setup plane is filled by the feature (based on location and frame
options). Thus only the sketch (PRO_E_SKETCHER) has to be defined by the
user
*/
/*
PRO_E_STD_SEC_METHOD Section Method PRO_VALUE_TYPE_INT
*/
/*
PRO_E_STD_SEC_METHOD required valid value PRO_SEC_SKETCH (= 25) defined in
ProStdSection.h
*/
/************************************************************************/
/************************************************************************/
/* PRO_E_SWEEP_TYPE */
typedef enum pro_sweep_type
{
PRO_SWEEP_TYPE_UNDEF = 0,
PRO_SWEEP_TYPE_MULTI_TRAJ = 128
}ProSweepType;
/************************************************************************/
/* PRO_E_FRM_NORM_SURF_SIDE */
typedef enum pro_frm_norm_srf_side
{
PRO_FRAME_NORM_SRF_SIDE_INSIDE = -1,
PRO_FRAME_NORM_SRF_SIDE_OUTSIDE = 1
}ProFrmNormSrfSide;
/************************************************************************/
/* PRO_E_FRM_NORMAL */
typedef enum pro_frame_normal
{
PRO_FRAME_NORM_ORIGIN = 0, /* normal to the origin traj. */
PRO_FRAME_PIVOT_DIR = (1<<9), /* "normal to projection" option */
PRO_FRAME_NORM_TRAJ_DIR = (1<<22), /* normal given by additional traj */
PRO_FRAME_CONST_Z_DIR = (1<<26) /* constant normal direction */
}ProFrameNormal;
/*
PRO_FRAME_NORM_ORIGIN: default. Normal provided by the origin trajectory.
PRO_FRAME_PIVOT_DIR: a direction must be provided in PRO_E_FRM_PIVOT_DIR
and PRO_E_FRM_ORIENT must be PRO_FRAME_CONSTANT.
PRO_FRAME_NORM_TRAJ_DIR: the index of the traj must be provided in
PRO_E_FRM_Z_CHOICE_BTN. Not supported in ProTK
PRO_FRAME_CONST_Z_DIR: a direction must be provided in PRO_E_FRM_CONST_Z
*/
/************************************************************************/
/************************************************************************/
/* PRO_E_FRM_ORIENT */
typedef enum pro_frame_orient
{
PRO_FRAME_MIN = 1, /* Automatic */
PRO_FRAME_NORM_SURF = 2, /* Normal to surface */
PRO_FRAME_CONSTANT = 3, /* option for PRO_FRAME_PIVOT_DIR */
PRO_FRAME_X_TRAJ = 4 /* Orient from X trajectory */
}ProFrameOrient;
/*
PRO_FRAME_MIN : Used for "Automatic" option.
PRO_FRAME_NORM_SURF: can be used only if the chain is from curves on surfaces,
such as edges, same feature projected curves,
curves from intersection.
PRO_FRAME_CONSTANT: must be set if and only if PRO_E_FRM_NORMAL is
PRO_FRAME_PIVOT_DIR .
PRO_FRAME_X_TRAJ: the index of the "X trajectory" must be filled in
PRO_E_FRM_X_CHOICE_BTN. Not supported.
*/
/************************************************************************/
/************************************************************************/
/* PRO_E_FRM_USER_X */
typedef enum pro_frame_start_x
{
PRO_FRAME_DEFAULT_START_X = 0,
PRO_FRAME_USER_START_X = (1<<27) /* user pick start x */
}ProFrameStartX;
/* Relevant only if PRO_E_FRM_ORIENT is PRO_FRAME_MIN.
If not default, then a direction must be provided in PRO_E_FRM_START_X.
A direction may be required (default is not available) in some
circumstances, such as linear non-sketched trajectory.
*/
/************************************************************************/
/* PRO_E_SWP_SEC_TYPE */
typedef enum pro_sweep_sec_type
{
PRO_SWEEP_VARIABLE_SECTION = 0, /* sweep variable section along the trajectory */
PRO_SWEEP_CONST_SECTION = (1<<23) /* sweep constant section along the trajectory */
}ProSweepSecType;
/* Only PRO_SWEEP_CONST_SECTION supported in Creo Parametric TOOLKIT. */
/************************************************************************/
/************************************************************************/
/************************************************************************/
/* PRO_E_END_SRF_ATTR */
typedef enum pro_sweep_end_srf_attr
{
PRO_SWEEP_END_SRF_OPEN = 0, /* Uncapped surface feature */
PRO_SWEEP_END_SRF_CAPPED = 14 /* Capped ends */
}ProSweepEndSrfAttr;
/************************************************************************/
/************************************************************************/
/* PRO_E_EXT_SURF_CUT_SOLID_TYPE */
typedef enum pro_sweep_feat_type
{
PRO_SWEEP_FEAT_TYPE_SOLID = 917, /* Solid Feature */
PRO_SWEEP_FEAT_TYPE_SURFACE = 942 /* Surface Feature */
} ProSweepFeatType;
/************************************************************************/
/************************************************************************/
/* PRO_E_REMOVE_MATERIAL */
typedef enum pro_sweep_rem_material
{
PRO_SWEEP_MATERIAL_ADD = -1, /* Protruded Feature */
PRO_SWEEP_MATERIAL_REMOVE = 916 /* Cut Feature */
} ProSweepRemMaterial;
/************************************************************************/
/************************************************************************/
/* PRO_E_FEAT_FORM_IS_THIN */
typedef enum pro_sweep_feat_form
{
PRO_SWEEP_FEAT_FORM_NO_THIN = 0, /* "Solid" (not thin) Feature */
PRO_SWEEP_FEAT_FORM_THIN = 128 /* Thin Feature */
} ProSweepFeatForm;
/************************************************************************/
/************************************************************************/
/* 4. PRO_E_STD_MATRLSIDE */
typedef enum pro_sweep_material_side
{
PRO_SWEEP_MATERIAL_SIDE_ONE = 1, /* Side 1 */
PRO_SWEEP_MATERIAL_SIDE_TWO = 2, /* Side 2 */
PRO_SWEEP_MATERIAL_BOTH_SIDES = 3 /* Both sides */
} ProSweepMatlSide;
/* Important : PRO_SWEEP_MATERIAL_BOTH_SIDES should be used with Thin and trim
features only. */
/************************************************************************/
/************************************************************************/
/* PRO_E_TRIM_QLT_SIDE */
typedef enum pro_sweep_trimqlt_side
{
PRO_SWEEP_TRIMQLT_SIDE_ONE = -1, /* Side 1 */
PRO_SWEEP_TRIMQLT_SIDE_TWO = 1 /* Side 2 */
} ProSweepTrimQltSide;
/************************************************************************/
/********************** Pre-Creo 1.0 SWEEP **************************
Please Note: This element tree is obsolete from Creo Parametric 1.0 release
Please use the tree documented at the start of this header file
Feature element tree
PRO_E_FEATURE_TREE
|
|--PRO_E_FEATURE_TYPE
|
|--PRO_E_FEATURE_FORM
|
|--PRO_E_SWEEP_SPINE
|
|--PRO_E_SWEEP_SECTION
---------------------------------------------------------------------------------------
Element Id Element Name Data Type Valid
Values
---------------------------------------------------------------------------------------
PRO_E_FEATURE_TYPE Feature Type PRO_VALUE_TYPE_INT PRO_FEAT_PROTRUSION
PRO_FEAT_FIRST_FEAT,
PRO_FEAT_CUT,
PRO_FEAT_SLOT
PRO_E_FEATURE_FORM Feature Form PRO_VALUE_TYPE_INT PRO_SWEEP
PRO_E_SWEEP_SPINE Trajectory Compound
PRO_E_SWEEP_SECTION Section Compound
PRO_E_SWEEP_SPINE and PRO_E_SWEEP_SECTION use subset element tree
structure of PRO_E_STD_SECTION.
In Rev. 20 sweep can be created under the default condition, i.e.,
For solid: solid not thin.
For surface: open ends not closed ends.
*************************************************************************/
PRO_END_C_DECLS
#endif